BPI-M64 GPIO Pin define

Banana Pi 40-pin GPIO:

Banana Pi has a 40-pin GPIO header that matches that of the Model B+ Raspberry Pi. Following is the Banana Pi GPIO Pinout:

GPIO Pin Name Default Function Function2:GPIO Function3
CON2-P01 VCC-3V3    
CON2-P02 VCC-5V    
CON2-P03 TWI1-SDA PH3  
CON2-P04 VCC-5V    
CON2-P05 TWI1-SCK PH2  
CON2-P06 GND    
CON2-P07 PH6 PH6  
CON2-P08 UART2-TX PB0  
CON2-P09 GND    
CON2-P10 UART2-RX PB1  
CON2-P11 PH7 PH7  
CON2-P12 UART2-CTS PB3  
CON2-P13 DMIC-CLK PH10  
CON2-P14 GND    
CON2-P15 DMIC-DIN PH11  
CON2-P16 UART2-RTS PB2  
CON2-P17 VCC-3V3    
CON2-P18 PD4 PD4  
CON2-P19 SPI1-MOSI PD2 UART4-TX
CON2-P20 GND    
CON2-P21 SPI1-MISO PD3 UART4-RX
CON2-P22 PC0 PC0  
CON2-P23 SPI1-CLK PD1 UART3-RX
CON2-P24 SPI1-CS PD0 UART3-TX
CON2-P25 GND    
CON2-P26 PC2 PC2  
CON2-P27 PC4 PC4  
CON2-P28 PC3 PC3  
CON2-P29 PC7 PC7  
CON2-P30 GND    
CON2-P31 PCM0-BCLK PB5
CON2-P32 PCM0-DIN PB7  
CON2-P33 PCM0-SYNC PB4  
CON2-P34 GND    
CON2-P35 PCM0-DOUT PB6  
CON2-P36 PL9 PL9  
CON2-P37 PL12 PL12  
CON2-P38 PL7 PL7  
CON2-P39 GND    
CON2-P40 PL8 PL8  

CSI Camera Connector specification:

The CSI Camera Connector is a 40-pin FPC connector which can connect external camera module with proper signal pin mappings. The pin definitions of the CSI interface are shown as below. This is marked on the Banana Pi board as “Camera”.

CSI Pin Name Default Function Function2:GPIO
CN5-P01 NC  
CN5-P02 GND  
CN5-P03 CSI0-SDA PE13
CN5-P04 CSI0-AVDD  
CN5-P05 CSI0-SCK PE12
CN5-P06 CSI0-Reset PE16
CN5-P07 CSI0-VSYNC PE3
CN5-P08 CSI0-PWDN PE17
CN5-P09 CSI0-HSYNC PE2
CN5-P10 CSI0-DVDD  
CN5-P11 CSI0-DOVDD  
CN5-P12 CSI0-D7 PE11
CN5-P13 CSI0-MCLK PE1
CN5-P14 CSI0-D6 PE10
CN5-P15 GND  
CN5-P16 CSI0-D5 PE9
CN5-P17 CSI0-PCLK PE0
CN5-P18 CSI0-D4 PE8
CN5-P19 CSI0-D0 PE4
CN5-P20 CSI0-D3 PE7
CN5-P21 CSI0-D1 PE5
CN5-P22 CSI0-D2 PE6
CN5-P23 GND  
CN5-P24 CSI0-AFVCC

Display specification:

MIPI DSI (Display Serial Interface)

The display Connector is a 40-pin FPC connector which can connect external LCD panel (MIPI DSI) and touch screen (I2C) module as well. The pin definitions of this connector are shown as below. This is marked on the Banana Pi board as “DSI”.

DSI Pin Name Default Function Function2:GPIO
CN6-P01 VCC  
CN6-P02 IPSOUT  
CN6-P03 VCC  
CN6-P04 IPSOUT  
CN6-P05 GND  
CN6-P06 IPSOUT  
CN6-P07 GND  
CN6-P08 IPSOUT  
CN6-P09 NC  
CN6-P10 GND  
CN6-P11 NC  
CN6-P12 DSI-D0N  
CN6-P13 NC  
CN6-P14 DSI-D0P  
CN6-P15 NC  
CN6-P16 GND  
CN6-P17 TWI0-SDA PH1
CN6-P18 DSI-D1N  
CN6-P19 TWI0-SCK PH0
CN6-P20 DSI-D1P  
CN6-P21 CTP-INT PH4
CN6-P22 GND  
CN6-P23 CTP-RST PH8
CN6-P24 DSI-CKN  
CN6-P25 GND  
CN6-P26 DSI-CKP  
CN6-P27 LCD-BL-EN PD5
CN6-P28 GND  
CN6-P29 LCD-RST PD6
CN6-P30 DSI-D2N  
CN6-P31 LCD-PWR-EN PD7
CN6-P32 DSI-D2P  
CN6-P33 GND  
CN6-P34 GND  
CN6-P35 LCD-PWM PL10
CN6-P36 DSI-D3N  
CN6-P37 GND  
CN6-P38 DSI-D3P  
CN6-P39 NC  
CN6-P40 GND  

UART specification:

The header CON4 is the UART interface. For developers of Banana Pi, this is an easy way to get the UART console output to check the system status and log message.

CON2 Pin Name Default Function GPIO
CON2 P03 UART0-TXD PB8
CON2 P02 UART0-RXD PB9
CON2 P01 GND  

results matching ""

    No results matching ""